Cambridge Education

How to Replace a kia key fob replacement cost Sportage Replacement Key

For many Kia models, the key contains a built-in keyless entry system. This key usually resembles an electronic remote and is able to be replaced with a new one from a 2012 kia sportage key fob replacement dealer or a locksmith.

Key fobs may stop working for a variety of reasons, such as the battery of the coin is dead, worn buttons signals, water damage, signal interference and a faulty receiver module. Here are some tips to assist you in getting your Kia sportage replacement key working for good.

How to replace the remote key or smartkey?

The battery inside your 2013 kia sportage key fob Programming's smart key will eventually need to be replaced, whether it's a remote, a push-to-start key or a regular key that doesn't have an electronic transponder. This is particularly relevant if your car displays a message telling that the remote or smart key is not powered by the battery.

Luckily, it's quite simple to do. To replace the battery on the keyfob remove the mechanical key from the slit at the back of the fob. Then, pull the cover off. Inside the key fob there will be a small screw that holds the battery in the correct position. By using a small screwdriver take the screw off and remove the battery that was in place. Then, insert the new one and close the slit inside the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors unlock and lock in the same way, you're good to go! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or when you need to run errands around Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming done. This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If your key requires to be reprogrammed, you must be aware of the number printed on the tag that identifies the key and keep it in a secure location.

How to replace the battery

If your kia sorento key fob programming key fob isn't responding to pressing the lock or unlock button on the fob, this is a clear indication that the battery needs to be replaced. A low battery may also cause other problems like the check engine light turning on or a delay in cranking the engine. Fortunately replacing the battery on the key fob is a fairly simple DIY task that requires only a few tools.

Before starting the process, make sure that your vehicle is turned off and that all doors are closed. Find the small metal or a plastic piece at the bottom of the key fob. Jiggle it until the key pops out. The key can be inserted into the driver door handle to unlock your car.

To replace the battery in the key fob remove the rear cover. Use a pry tool to loosen the latch that holds the black negative cable. Remove the old battery, and then align the new one to ensure that the "+" positive side faces your face and the "negative" negative side is facing the fob's metal electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or breaking the metal contacts.

Once the new battery has been installed then turn the key fob off and back on in the ignition repeatedly until the door locks. You can then test the Kia's Key fob again to confirm that it's working properly.

How to replace the smart key

There is a possibility of having the standard keyfob or Smart Key based on the model of Kia Sportage. The smart key features an embedded mechanical key blade, however, the standard key fob does not. Both key fobs contain batteries that eventually require replacement. Fortunately, it's an easy task that will take about two minutes.

Be sure to turn off your Kia, and be on a flat and well-lit surface prior to you begin. Keep in mind that there are tiny pieces inside the fob that could fall out if not careful.

The release button for the small size is located on the lower backside. This will be either an oval or circular slot. When you press it button, the mechanical blade will pop out and you can then open the key fob.

Once you have the key fob open and you are able to remove the old battery and replace it. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. After installation, you should be able to lock or unlock your vehicle with your key fob - even if your engine isn't running!

How do I replace the mechanical key?

The kia key fob replacement near me key fob is a great convenience that lets us lock and unlock our vehicle with the click of the button. But, as with all devices, it can have problems occasionally. There are ways to address these issues and keep your key fobs functioning for an extended period of time.

One of the most frequently encountered issues is a low or dead battery. The fob could be able to cease working or stop working at times. If this is the case it is time to replace the battery a new one.

If this doesn't fix the issue then try using a normal flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a new one.

When the new battery is in, shut and open the doors using the mechanical key (every Kia fob has an emergency mechanical key that can fit in the slot). Test the key fob to ensure that it's working properly. If the key fob isn't working, contact an expert locksmith or dealer to solve the problem. To avoid locking outs in the future, make sure you get an emergency key that can work on all trunk and door cylinders.